Share your ENARSI v1.1 Experience

Passed exam – VRF lab took way too longer , ended up with 20min for the remaining 40- managed to get to 38 when exam timed out- If you know the subject well- time-management is the key to pass-GOOD LUCK

@INF CONGTATS, QUESTIONS ON THIS SITE IS VALID?

Yes, they are

@Passed

3 labs:

IP SLA & NetFlow

DMVPN Phase 2

VRF & EIGRP (similar to the one on that site, with ACLs blocking EIGRP)

43 questions covering Parts 1–8, with about 6 new questions.

Good luck to the next candidates.
Take the time to practice the labs on this site several times and try to understand the concepts.
This will help you avoid losing too much time during the exam.

Just passed.
Same 3 labs as the ones mentioned by the others before : DMVPN, VRF+EIGRP, DHCP+IPSLA+NetFlow.
43Q that were mostly from here… about 5 new questions.

I passed the exam today.

This was my second time. It was tight but I managed to finish 40/43 questions.

Three labs:
1. DHCP+IPSLA+Netflow: DHCP was configured with the wrong default gateway in the server and I had to configure the ip helper on the switch vlan interface. IPSLA was based on http and I had to enable the responder functionalities on the receiver. In my first exam Netflow was based on UDP and top talkers but this time was something about the statistics disappearing every 15 seconds and required 5 minutes. I configured the cache time but I don’t know if that was 100% right

2. DMVPN: Almost the same as before but in this case I had to remove the tunnel source from the spokes and configure the IPSec Transform and profile in the hub (copying from spokes)

3. EIGRP+VRF: This one had the new request; to advertise a summary route from R6 without using the ip summary eigrp command and the router was configured as eigrp stub static. For this one I created a manual static summary route to null0 and redistributed static in EIGRP at R6.

My strategy for the lab was to get them done within 10 minutes. That would allow about 60 minutes for the questions section. The first and second lab were right between the 10 minutes mark, but the third lab took me a little bit longer to tshoot the required pings. About 15-20 minutes.

I had about 50 minutes for 43 questions and still managed to complete 40/43.

Most questions from here, maybe a couple of new questions and they take time to analyze but you should be good if you know the concepts and practice the questions here.

Best of lucks.

Just passed the exam. Same lab that was posted by others but with different tasks but related. Practice the labs provided here. No drag and drop. About 5-10 new multiple-choice questions. Goodluck!

I pass the exam.
3 Labs and 42 questions and 1 Drag and Drop VRF.
All lab from here with some changes.
Lab 1, Dhcp helper address and IP sla start and track command.
Lab 2, Vrf and Eigrp connections like VRF & EIGRP Sim (Draft Version), Wrong AS, no auto-summary, and Acl and prefix-list preventing the adjacency of the eigrp.
Lab 3, Hub and spoke phase 1 on the hub and advertise the Spoke routes to each other using the EIGRP.

Obs1:. There were three questions that are not here, but I think they are just test questions without scoring.
Obs2:.Time needs to be used well in the Labs, otherwise there is little time left for the multiple-choice questions.

Good luck everyone and thanks Networktut !!!!

I PASSED the exam today!

3 Labs 37 questions and 3 Drag and Drop MPLS, VRF and PBR(New PBR DND but easy to answer if you know the concept)

LAB
1. vrf + eigrp
2. dhcp static + ip sla dns + ip flow sampler = I didn’t manage to resolve the ip sla dns. command to verify: ‘show ip sla summary’
3. dmvpn phase1 where only Hub R1 you need to configure

If I can do it, you can do it too! goodluck aspiring CCNPs!

Hello, there are 3 dmvpn SIMs, which one are is coming in the exam?

I can’t find the labs here which you guys are mentioning.. sla, eigrp-vrf

Congratulations to those that have passed. Did y’all use the === Lab Sims for ENARSI v1.1 === from here to prepare for your lab? Could you also share any other lab resource(s) y’all used if any.
Writing end of April. Thanks.

I passed the exam today. I failed it exactly one week ago, miserably. It took me an hour to get through the labs and I didn’t finish all the questions. If I had 15-20 more minutes I may have passed last week. I had the same labs today as I did last week, and that was key to passing this time around. I had eigrp/vrf lab, ip sla/dhcp/flow monitor lab, and dmvpn phase 2/ipsec lab.
None of the labs were really from this site that I could tell, although as long as you got the concepts down you should be able to power through them.

eigrp/vrf lab, architecture is the same as what’s on this site. The eigrp process was configured incorrectly on the “ISP” routers in the middle, so had to adjust that on those. Network statements need to be correct of course. Then I think the last thing was r3 had authentication configured and r4 didn’t.

ip sla/dhcp/flow monitor lab – dhcp pool was wrong on the dhcp server, then the ip helper address had to be configured on the SVI on the switch upstream from the dhcp client. IP SLA – can’t really remember on this one, I remember running the show command for ip sla and saw it was successful so I think I just ended up adding the track to the static route, checked the route table and it looked good. flow monitor – not sure if I got this right, but I think on the interface i saw the flow monitor was only inbound and I just added outbound as well and could see packets in the stats.

dmvpn/ipsec – All configurations had to be done from the hub, but you will have to check on the spokes to see what’s configured wrong. IMPORTANT – on this one the dmvpn doesn’t come up until you finish both tasks. It says that in the tasks section, but only at the bottom. I didn’t see that first and wasted way too much time on it. I think the missing command on the hub for dmvpn was “ip nhrp map dynamic multicast”. To get the ipsec tunnels up the tranform set had to be configured on the IPsec profile.

Most of the questions I had were from the “New Enarsi questions – 1 – 8”. I used CBT nuggets for initial lectures, then pearson VUE for tests to see what I needed to work on (can test yourself on specific topics on their testing engine, it’s awesome). Then after I felt I knew everything really well, I came here and spent hours upon hours looking through the questions. I highly recommend making sure you understand everything in every question as that will help you fly through the questions a lot faster. If you don’t understand the explanation on this site, copy/past in AI to talk it out. You don’t want to spend much time on these questions, so knowing them from this site is key. It took me 45 minutes to get through the labs this time around and I still barely got through all the questions. Good luck everyone!

Are the labs different now? Should we wait till the next update before taking the exam?

Failed today(

Lab’s take too much time
1. dmvpn phase 2 with eigrp but really different tasks, i was trying to my best
2. Dhcp & netflow (gues will correct)
3. vrf with eigrp (task 2 ) but something was not correct, and im just skipped

So don’t have much time to the question, so last 5-8 questions without answers

Could you tell me, when i can retake this exam?

@abobus,

you can retake after 5 days from your scheduled exam.

don’t get down by it. prepare for it better then get back to it!.
I guess time management is really the key to pass this.

how you guys are paying… I’m stuck on paying and scheduling the exam… my country, um… haaa, it’s shit. our card payment system have been banned. Any hacks?

Hello,
what do you think guys i am ready if i pass the composite test more than 20 times(90%+)? i mean ready for the questions i dont mean the lab part of the exam.
Good Luck!

When will the v1.2 exam go live?

Passed. 40 questions, 3 labs. VRF & EIGRP, DMVPN Phase 2, DHCP/IP SLA/NetFlow. Probably 7 new questions not seen in v1.1 and 1-8 new questions. VRF/EIGRP – Had to disable EIGRP auto-summary by doing: router eigrp 10 / no auto-summary. Was enabled on 3 or 4 of the routers. Sim was flipped so that R1, not R5 was the one with the wrong ASN of 600 instead of 500. R3 did have an ACL blocking traffic. DMVPN Phase 2 – was most like SIM 1 and 2 from this site. Tunnel number was 10. Can’t remember if there was a tunnel key. I did have to do no tunnel destination to enable tunnel mode gre multipoint. I only had to set the mtu at like 1340. There was no change in TCP segment size. The IPSEC profile was already created. Just had to add it to the tunnel inteface. Might have been a holdtime, but there definitely wasn’t a registration timeout. There was a part of one of the tasks that mentioned ensuring that OSPF was configured correctly. ip ospf network broadcast was only enabled on the hub. Had to add it on the spokes. I forgot to change the ospf priority to 0. It might have been set on the hub, but I can’t remember. Final check was pinging the loopback of the hub, and it worked, so I guess the hub was already the DR. DHCP/IP SLA/NetFlow – Topology was similar to the one in the sim, except R2 was diagnal to the upper right, R6 was directly to the right of SW1, and R4 was connected to SW1 instead of R3. Task 1 and it’s solution is valid R4 needed to have e0/0 going to Sw1 set with ip address dhcp client-id ethernet 0/0. I have no idea on the DNS issue. R6 was the DNS server and R2 had set up a SLA to monitor DNS on R4. It was just showing failures no matter what I did. NetFlow – Okay, the monitor was set up on SW1 to monitor flow going to the “ISP” which was passed R6 on the right. I had to do no ip flow monitor just like in the task, add the sampler, but it was output, not input because it was measuring traffic going out of the switch towards the ISP. I had to do ip flow egress (did ingress too because why not) then ran show sampler sampler-1 to see that it was finally getting sample info. I assume that’s right, but take it with a grain of salt. Good luck everybody else. I did CBT nuggets and this site to study. Did big test until I got finally finished one with 100%. @network tut , dear God, please find a way to clean out some of these questions. Close to 800 questions to go through about killed me.

please, add the new questions!!

This Questions still a valid or not?

Did anyone wrote the exam this week? Please share your experience

Unfortunately I didn’t pass the exam a few days ago.

I found a new lab regarding configuring eigrp with vrf. Then I had a lab on ipsec configuration, but it seemed already configured properly. Maybe I didn’t understand the requests well, I’m not a native English speaker and I panicked. I’ll try again. Many questions are present here, but there are also new ones. I don’t know if this is the best time to take this exam.

I’m only counting 80 questions. Is that all that we need to study along with the labs, or is there a larger pool that I’m missing?

I just passed today, 3 lab + 40 MCQ
MCQ I think is 100% from here.

1. DHCP + IP SLA Lab.
DHCP change the SW2 VLAN with IP help address for R1 IP address
Update DHCP pool GW on R1.
IPSLA Not sure, it need monitor R5 Ip 5.5.5.5 with port 80, I tried but still not up.

2. DMVPN, configure HO router and BR1 & BR 2 router.
remove BR1&BR2 tunnel destination.

3. VRF + EIGRP
remove auto summary for the router.

Thanks Networktut and All of you.
Good luck and all the best

I can no longer get accommodations for non-native English speakers. Does this happen to anyone else?

@KW Congrats! what do you think questions is a valid?

Passed, everything from poster KW (March 31st, 2026) post’s is everything I got.

Hi there, anyone taken the exam recently, please share the experience!