Share your ENARSI v1.1 Experience

Passed exam today!

– 3 Labs + 43 MCQ questions.
– Labs:
DHCP – dhcp static assignment ip 10.1.2.141 for R6(client)
IP SLA – DNS ip sla down from (R6 dns client) to (R4 dns server)- couldn’t figure out the issue and left it unresolved.
Flexible Netflow – SW1 missing flow exporter, configure & match it to monitor then apply it outbound on int E0/2 with a pre-configured sampler
—————————————————————————————————
DMVP:
Spokes are pre-configured but with wrong nhrp map multicast hub details & tunnel source of loopback interface & had to remove tunnel destination.
Hub, required to configure tunnel interface based on tunnel configs from the spokes, allow dynamic mapping & disable eigrp slit horizon & next-hop-self. apply ipsec profile
————————————————————————————–
VRF & EIGRP:
R2 & R3 – need to configure eigrp routing process 10 with address family for Sales & Admin vrf’s
R6 got incorrect AS 500, need change to 600. no ACLs
required to configure no auto summary R1,4,5,6

– MCQ, almost all the questions were from here, only noted 3 new questions which I answered based on my knowledge.

comment: challenge is not the content but time keeping, try do 1 lab in 10min.

GOOD LUCK to everyone still to write!!!

Passed exam today!

– 3 Labs + 43 MCQ questions

-LABS:
DHCP + IP SLA + Netflow
DMVP phase II
VRF + EIGRP

Almost all questions are from here, saw 3 new which were easier to answer.

GOOD LUCK!!!
thanks all & Network tut

I passed the exam today!

3 Labs + 43 MCQ

1) DHCP + IPSLA
– Enabled the ip helper-address on sw10 didn’t help
– Was getting following error.
R2(config)#ip dhcp pool Branch-1
R2(dhcp-config)#network 10.1.2.0 255.255.255.0
R2(dhcp-config)#host 10.1.2.239 255.255.255.0
% This command may not be used with network, origin, vrf, or relay pools.
R2(dhcp-config)#
– Also attempted by removing “network 10.1.2.0 255.255.255.0” to allow host & client-identifier commands.
– Changed the command “ip address dhcp client eth0/0” on R6 still failed to gate IP address assigned.

IP SLA
– “ip sla” is already configured.
– configure “ip sla start” and “track” commands.
– “show track” shows whether SLA is okay or not.
– Check the “ip route” commands.

2) DMVPN
– Ensure HUB configuration.
– can take help of spoke configuration
– Ensure two commands “ip nhrp map multicast dynamic” and “no ip split-horizon eigrp 1”

3) VRF and EIGRP
– Make sure network/wildcard mask commands under EIGRP are properly configured
– Remove access-group on R3 to allow communication between R3 and R4
– Advertise R4 Loopback in to EIGRP as task says to ping R4 loopback from R1

43 MCQs in total. Most questions are from Networktut, with only 2–3 outside sources. Practice the ENARSI Composite Quizzes until you consistently score at least 95% and feel fully confident.

We have multiple DMVPN Sims, which one is DMVP phase II?

Passed exam today!

– 3 Labs + 43 MCQ questions

-LABS:
DHCP + IP SLA + Netflow
DMVP phase II
VRF + EIGRP

Almost all questions are from here, saw 4 new which were easier to answer.

GOOD LUCK!!!
thanks all & Network tut

Guys! @Dante, @Siva, @Jigga, @DovaDova, can you please provide me the name of DMVPN from this website which came in the exam. Is it “DMVPN Configuration Sim”, “DMVPN Configuration Sim 2” or “DMVPN Configuration Sim 3”

Hello we have 3 SIMs for D M VPN. Which one is coming in the exam?
SIM 1,2 or 3. Please can someone answer that

Someone mentioned in dmvpn exam they were required to disable split horizon and next hop self – that should be all you need to know in order to determine which phase it was and figure out what simulation you need to focus on.

Thanks Donald J trump.

Anyone who recently took the exam!

Did you see any drag-and-drop questions?

In the LABO exam, one question appeared that is not in this set. The content was about IPsec and mGRE, but the conditions were completely different. I am looking for information from those who took it recently.

He did a lab on DHCP, IP SLA, and NetFlow.
DHCP is the same, but there is a problem with tracking multiple routes using SLA.

It is almost the same as the VRF & EIGRP simulator (draft version), but the routes were not learned,
and he could not ping the loopback.

There were no drag-and-drop questions. As for multiple-choice questions, only questions similar to those here appeared. Unfortunately, I failed, so I need to prepare for command questions.

excusme!!!!
how can i get question’s answers and labs in this site , i dont understend .

@Acuna, you need to purchase a premium membership. (Click the top right-hand corner)

I had a positive experience with CertsTopic. It helped me prepare effectively. I passed.

Does anyone pass the exam? Please share experience

Just passed this afternoon.

MCQ is 100% here parts 1-8. No Drag and Drop.
However, with the labs, ill be honest, i didn’t complete any of them. LOL. i was paniking throughout each of the labs.

1. EIGRP + VRF LAB – EIGRP AS 500 global, AS 100 – VRF FINANCE, AS 200 – VRF ADMIN
2. DMVPN + OSPF + IPSEC_PROFILE
3. DHCP + IPSLA + FLOW CACHE

– Practice the labs on this site and understand the concept. The exam will test you on different senarios but based on the skeleton of the LABS here. Good luck to you all. i enjoyed viewing the experiences of others.

Are the labs that appear on the actual exam available here with the premium subscription? I don’t currently have it, and the labs I see aren’t the ones that appear on the exam. I’d like to confirm this before subscribing.

Thanks.

Does anyone pass the exam? Please share experience

If you haven’t got the premium subscription, you are missing out @CiscoLover

Thank you for your reply @FS3851, but it doesn’t clarify my specific question. Could you please tell me if the labs listed on the exam are available here? For example, they are listed on digitaltut.com for the ENCORE exam (with a subscription, of course). Thank you.

can someone say how close the labs are to the real labs

Just passed yesterday

MCQ is mostly from here, but I had 17-18 new questions. No Drag and Drop.

1. EIGRP + VRF LAB – EIGRP AS 100 global, AS 500 – VRF Sales, AS 600 – VRF ADMIN
2. DMVPN + OSPF + IPSEC_PROFILE
3. DHCP + IPSLA + FLOW CACHE

– Practice the labs on this site and understand the concept. The exam will test you on different senarios but based on the skeleton of the LABS here.

Don’t panic

@MrLAVA
17-18 new questions are a lot. Are you sure they are new?

@mrLAVA

Did you refer all of the 1-8 mcq or ???

I took the exam today and failed!
3 SIMs
1. EIGRP + VRF LAB – EIGRP AS 10 global, AS 100 – VRF Finance, AS 200 – VRF Security
2. DHCP + IPSLA + FLOW MONITOR
3. DMVPN + EIGRP PHASE 2

About 3 questions I didn’t recognise.
I forgot to shut and no shut the interface on the DHCP SIM.

Just passed today

40 MCQ | 1 Drag and Drop | 3 LAB

LAB:
## DMVPN Phase 2 ##

## DHCP + IPSLA + FLOW ISP1-monitor ##
– Configure ip helper-address 10.1.1.1 on SW2;

## EIGRP + VRF LAB – EIGRP 10, AS 500 – VRF Sales, AS 600 – VRF ADMIN ##
– Configure VRFs on R2 and R3;
– Remove EIGRP 600 and configure EIGRP 500 on R1;
– Remove auto-summary in all Routers;

Can anyone please confirm whether copy-and-paste option is available in the CLI?

Ladies and Mostly Gentlemen, i passed the exam today and have both good and bad news

good news is that the questions 1-8 are VERY VALID
i genuinely only saw one question that i had no seen before but everything else, including the wording was exaclty the same. YAY

Another good news is that the DHCP and VRF labs are very similar to the ones on this site. I recommend studying all of the varriants tho because they mixed it up.

Now here comes the bad news. For the DMVPN lab, i thought i would cruise through it. Just like practice i thought it will ask me to configure phse 2 on either the hub or the spoke (which is easy if you memorise the structure of the config) But no. They came out asking about crypto ipsec transform-set config matching and also crypto isakmp config. I had absolutely no idea. i did get the dmvpn link up on one router but the other one kept having trouble. with the crypto isakmp part, i had not seen a lab like that before so i don’t even know what to say to help you guys. I barely remember it sorry.

thank you networktut still, the questions came in very handy.

Can someone please map the labs in the website vs the one in the exams.
e.g there are two for DHCP and IP SLA etc.
DHCP IP SLA & NetFlow (Draft Version)
DHCP IP SLA & NetFlow 2
Thanks

@FS3851 in this lab, you must confiugre transoform-set under the profile. that was the main problem on the hub router.